Line out converter sound quality

Many folks don't want to replace their factory radio, because of its look in the dash or the fact they have a leased vehicle. However, they can still upgrade the sound in their system by tapping into the speaker wires for the audio signal. A line output converter provides the connectivity needed to do it in most cases. A: Normally you would cut the speaker wires and run them to the LOC, then run new speaker wires from your amp back to the other side of the cut wires to send signal to your speakers.

A: Some converters provide more features and power handling than others. So, it's important to know the total power output of the signal going into LOC you choose. We list the maximum RMS wattage that can go into to the line output converters we sell. In terms of added features, some converters include higher preamp output voltages, which keeps the audio signal to your amp ultra-clean.

Others can include bass restoration circuitry or equalizers on board too. It's all a matter of the power you'll be working with and how much you want to tweak your system. A: Yes, definitely. Amplifiers that offer speaker-level inputs don't require a separate line output converter to tap into existing speaker wires to get their signal. Many powered subwoofers offer this feature, too. The speaker-to-line level conversion is done inside the amplifier.

Check out our selection of amplifiers with speaker-level inputs. This amp includes an adapter that lets you connect your speaker wires directly, without needing a line output converter.

The adapter plugs into the amp's "high level input" connection. A: As mentioned above, some upgraded converters offer additional features that an amplifier you're considering doesn't have, such as on-board equalizers, higher voltages on the preamp outputs, or restoration circuitry that resets the factory system's equalizer to a flat setting. This lets you start from scratch in terms of setting up the sound the way you want it.

So, it really depends on what type of system you want to create. A: Line output converters are sometimes also needed to install a new stereo in a vehicle with a separate factory amplifier. They often offer gain adjustments that let you balance the output from new radio to the input sensitivity of the factory amp for the best sound.

So even if you're working with a radio with no RCA outputs, you can still add some amplification to your speakers or add a subwoofer. If you have additional questions, check with one of our knowledgeable Advisors. We're here to help. If I want a sub that takes rms and my amp can push like rms to that sub then if I get a line out converter that has rms most of these converters on this page say rms then will my amp and sub only get rms and be underpowered?

One of them is tapped into the rear speakers going to a mono amp for two subs, now I'm looking to use a separate 4 channel amp to power the speakers, can I just tap the front speakers and run them to the LOC or is there a better or different way? I really don't want an amplified door chime.

Once hooked up to the LOC do I just use 2 rca splitters to go to the 4 different channels on the amp? I'm so confused?????

I'm helping a buddy of mine install an amp and subwoofer to his Charger. I know how to tap into the speaker wire for the signal to feed into the amp and send to the sub with the LOC. The car also has a factory amp. Could I still use the same concept to run a 5 channel amp to get better sound through aftermarket speakers while still keeping the factory radio?

I connect to line output to the wire that went to the factory sub then went my amp question is is since I tied into factiry sub wires that means the factory amp is before my aftermarket amp correct so that factory gonna hinder my new amp correct. Where would it be best to install an LOC? Closer to the head unit or the amp.

Hi My car is completely stock and has a factory amplifier somewhere between the radio and door speakers. I know this because ac voltage on stock speakers are 12v. Question is, do I connect the LC2i between the radio and factory amp or after the factory amp? Thanks in advance. Should you set your amp to high or low level input when using a LOC?

I tapped LOC into the speaker wires right after my factory amp in the dashboard. And then ran RCAs back to the amp. Here's a step-by-step guide to installing a car amplifier, including how to run the cables through your car and how to wire the amp.

What size of wire should you should use when installing an amplifier? Use our handy wire gauge chart to find out. Where should I mount it? What wiring do I need? What size fuse and power wire? Car amplifier audio terms - like watts, volts, and efficiency - are explained.

There are many ways to connect subwoofers to an amplifier. Our wiring diagrams will help you find the best way to wire your subs and amps so you'll get the best performance out of your gear. These wiring diagrams illustrate how amplifiers connect to your audio system, which will make it easier to shop for the gear you need for the system of your dreams.

How much power and how many channels do your car speakers need? This guide will help you choose the right amplifier for your car's sound system. Confused about wiring your subs and picking the right amplifier? Crutchfield will get you on the fast track to big bass with this simple guide. If you ask us, a car stereo system should include much more than a stereo and a pair of speakers. Adding components like satellite radios, subwoofers, amplifiers,.

For free personalized advice, call Our Advisors have listened to most of the speakers we carry, and can help you make the best choice for your system. Close contact box. Call See our hours Our hours Hours 7 days a week. Looking for International Support? Connect ID. Any GTOTM signal capturing capacity of LC2i can auto turn on the remote on lead and can detect any signal coming from the factory head units.

This device can receive the factory level signal up to watts per channel to amplify them as per the user demand level.

Once all these signal converters into high-quality audible sounds, it transfers all of them into any aftermarkets with all its amplifications. The Two-channel of Active Speaker Level Input of this device can accept diverse output with discrete level controls. LC2i is not only a line out converter, but it has also one super functioning ability. For over 33 years, LC2i is giving gorgeous audio quality among many car radio users.

The mind-blowing performance from your car stereos system, impressively very possible with one renowned LC2i. KISLOC 2-channel line out converter is included 2-channels to accept 50 watts per channel input signals with a delivering capacity of 8 volts output as well.

This smart line out converter is compatible with OEM radios. OEM radios have short circuit protection and it can enhance one important quality in your factory sound system. To meet the amp needs for the input of a speaker-level signal, this device can lower any amplified signal below the line level.

Thus, it can control each audio signal accepting on each channel. KISLOC 2-channel line out converter can modify your factory radios along with the Open-Circuit protection by applying ohm load per channel. However, the audio signal you got from this LOC is very clear and audible also. It is a lightweight, small, and compacted device and can be installed through a very easy process. You can buy this converter at an affordable price and with one year of warranty. PAC LP is a high-power line output converter that can use any head unit of your car.

This PRO series is manufactured in precise engineering works so that it can deliver the best quality sound upon optimization of the audio level in between the factory head unit and the amplifiers.

The Ultra-compact housing and a high power included in this machine, make it capable to accept 55 watts per channels very clearly. The short circuit protection capabilities of this device can enhance the Bass quality and can reduce a higher bass roll-off as well. It is a very affordable product. After reading all the product reviews I had described above, already you may have decided which LOC you should buy actually.

However, if you still in the confusion to choose a perfect line out converter, you can go for other brands. Now I will include some factors which you should observe before purchasing the converter very efficiently. A renowned brand of any perfect line out converter will never compromise with their quality and service. Though you may expanse relatively a higher for a reputed brand, I suggest picking any reputed LOC brand. Do you have any intension to buy the LOC frequently after a short interval?

If no, then choose a top-rated brand for your LOC. Usually maximum basic line out converter included 4-channels 2 for input channels and 2 for output channels. However, varying on the LOC brand, the number of channels can extend up to 6 as well. An increased Channel number can provide more connection to the amplifiers and the speakers.

So, if you want more channel, go for the LOC models which has more channels. LOC with upgraded features and specification enhance user satisfaction in many angles. As a result, the sound from headphone outputs is usually slightly muffled compared to the clean sound from the line out.

On the other hand, line-level output signals are very pure. They are optimized to produce virtually little or no noise and distortion. This is because they are not subjected to any form of amplification that can introduce distortion in the audio signal. In theory, since line out signals are of low signal strength, they are less likely to get degraded.

Line out signals has a source impedance within the regions of ohms and more. They are meant for driving loads that have high input impedance. Line level outs are optimized to produce low noise and distortion when used with high impedance loads. Unlike line outs, headphone outs have a low source impedance. They come with impedance between 16 ohms and ohms. Headphone outs are designed to drive lower impedances posed by headphones.

Headphone outs are optimized to drive high current with reasonable distortion and noise with low impedance loads. In conclusion, a headphone output is optimized for lower impedance loads and is capable of supplying more power to these loads.

A line-out, on the other hand, is optimized for driving higher impedance loads. You can use the headphone output of your device as a line out. A headphone out can be used to send line-level signals to other audio devices, provided the volume is not too high. This will help prevent distortion and reduce noise.

Headphone outs can be used as substitutes for line outs. Some audio devices like keyboards, etc. As the owner of such a device, you would have no option but to use your headphone out as a line out.

Although headphone outputs are not as pure as line output signals, they can be used as line-outs without significantly reducing the final sound quality produced. This simply means it can give you good sound with just a little noise and distortion in performance. However, this result varies from one device to the other.

But as a rule of thumb, just keep the volume down. This will prevent any distortion and reduce any noise. Though a headphone out can be used as a line-out, you can experience a little noise and distortion in the final sound output. This means you are more likely to get better and cleaner results with a line out. You can plug headphones into a Line Out, but the audio will be barely audible, if audible at all through the headphones.